Magellan Paradox Instrukcja Instalacji Pobierz pdf (Strona 27)

Paradox Magellan Systems 27

• Auxiliary Panic: Panic keys [4] and [6] (page 25) or the

appropriate button(s) on a remote control (page 20)

have been pressed.

• Fire Panic: Panic keys [7] and [9] (page 25) or the

appropriate button(s) on a remote control (page 20)

have been pressed.

• Recent Closing: Reports when an alarm is generated

after arming the system within period defined by the

Recent Close Delay (see page 30).

Section [140]

• Auto-zone Shutdown: A zone communicates more than

the programmed number of transmissions in a single

armed period (see page 17).

• Duress: A Duress access code is keyed in (see

page 14).

• Paramedical alarm

• Future use

Zone Tamper Report Codes

Section [141] to [144]

A report code can be programmed for each of the 16

available zones. Whenever a tamper or wire fault occurs on

a zone, the Magellan console can send the appropriate

report code to the central station identifying which zone was

tampered.

If Tamper Recognition (see page 24) is disabled, the

console will not report the occurrence of any tampers, wire

faults or tamper restores.

Zone Tamper Restore Report Codes

Sections [145] to [148]

A report code can be programmed for each of the 16

available zones. Whenever a tampered zone is restored, the

Magellan console can send the appropriate report code to

the central station identifying which zone has been restored.

If Tamper Recognition (see page 24) is disabled, the

console will not report the occurrence of any tampers, wire

faults or tamper restores.

System Trouble Report Codes

Section [149] to [151]

Whenever the system generates one of the instances listed

below, the console can send the appropriate report code to

the central station identifying the type of system trouble.

Section [149]

• Console Tamper: A tamper has been detected on the

console itself (see Console Tamper Supervision on page

33).

• AC Failure: Magellan has detected a loss of AC power.

Transmission of this report code can be delayed (see

Power Failure Report Delay on page 31).

• Battery Failure: The backup battery is disconnected or

battery voltage is ≤ (less than or equal to)6.9V.

• Timer Loss: The console has detected a loss in time or

clock failure.

Section [150]

• Future use

• Fail To Communicate: The Magellan console has failed

all attempts to communicate with the central station. The

report code will be transmitted upon the next successful

attempt.

• Wireless Low Battery: The battery voltage of an Omnia

wireless transmitter (motion detector or contact switch)

has dropped below recommended limits.

• Tx Supervision Loss: Check-in Supervision (page 24)

has been enabled and a transmitter is no longer

communicating with the system.

Section [151]

• Future use

System Trouble Restore Codes

Sections [152] to [154]

Whenever the system restores one of the troubles listed in

sections [149] and [150] (see System Trouble Report Codes

on page 27), the Magellan console can send the appropriate

report code to the central station identifying the type of

system trouble restored. If Telephone Line Monitoring is

enabled (see page 30), use the first two digits to program a

TLM Restore report code that the console can transmit.

Special Reporting Codes

Sections [155] and [156]

Whenever the system generates one of the instances listed

below, the Magellan console can send the appropriate

report code to the central station identifying the type of

system occurrence.

Section [155]

• Cold Start: The console was completely shutdown (no

battery, no AC) and then was restarted.

• Test Report: A test report has been generated

automatically (see page 31).

• Future use

• WinLoad Logout: The console has ended

communication with WinLoad.

Section [156]

• Installer logon: Installer has entered the programming

mode.

• Installer Logout: Installer has exited the programming

mode.

• Closing Delinquency: The last time the system was

armed is greater than the programmed Closing

Delinquency timer (page 23).

• Future use

Console Telephone Numbers

Magellan can dial up to two different central station telephone

numbers and one Pager telephone number. You can enter any

digit from 0 to 9 and any special keys or functions (see Table 9

on page 28) up to a maximum of 32 digits. If the number is less

than 32 digits, press the left [

ACTION] key (ok) to save the

message.

1 2 ... 22 23 24 25 26 27 28 29 30 31 32 ... 44 45

Komentarze do niniejszej Instrukcji

Brak uwag

Magellan Paradox Instrukcja Instalacji Strona 27

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Magellan Paradox