Magellan Paradox Instrukcja Instalacji Pobierz pdf (Strona 18)

18 Reference & Installation Manual

Intellizone Delay Timer

Section [065]: 010 to 255 seconds; Default = 48 seconds

Enter the desired 3-digit value into section [065] to

program the Intellizone Delay Timer.

Delay Before Alarm Report Code Transmission

Sections [001] to [016]: Zones 1 to 16; option [7]

Option [7] OFF = Delay alarm transmission disabled

(default)

Option [7] ON = Delay alarm transmission enabled

This feature is commonly used with Entry Delay zones to

reduce false alarms created by new users who may not

disarm the system in time. This feature works as follows:

• When an alarm condition occurs on a zone with this

option enabled, the console enables the bell/siren

output, but does not report the alarm to the central

station until the end of the Alarm Before Transmission

Delay.

• During this period, disarming the system disables the

bell/siren output and cancels the report code

transmission.

Alarm Transmission Delay

Section [075]: 001 to 255 seconds; 000 = Disabled;

Default = 0 seconds

Enter the desired 3-digit delay value into section [075] to

program the Alarm Transmission Delay.

Force Zones

Sections [001] to [016]: Zones 1 to 16; Option [8]

Option [8] OFF = Force zone disabled

Option [8] ON = Selected zone is Force enabled (default)

Any open Force zones at the time of arming will be

considered deactivated by the console. If during this period

a deactivated zone is closed, the console will revert that

zone to active status. Consequently, the console will

generate an alarm if the zone is breached.

Fire zones cannot be programmed with the Force Zone

option because the console will not bypass a Fire zone

when the system is being Force armed.

Zones 15 and 16 become Hardwire Zones

Section [095]: Options [1] and [2]

Option [1] OFF = Wireless zone 15 remains unchanged (default)

Option [1] ON = Wireless zone 15 uses the on-board hardwire

zone input 1

Option [2] OFF = Wireless zone 16 remains unchanged (default)

Option [2] ON = Wireless zone 16 uses the on-board hardwire

zone input 2

The Magellan console comes with two on-board zone inputs,

hardwire zone inputs 1 and 2. Section [095] options [1] and [2]

allow you to convert zones 15 and 16 from wireless to hardwire

by allowing you to connect hardwire detection devices (i.e. door

contact) to zone inputs 1 and 2.

• With section [095] option [1] ON, zone 15 is connected to

zone input 1.

• With section [095] option [2] ON, zone 16 is connected to

zone input 2.

EOL (End-Of-Line) Zones

Section [095]: Option [3]

Option [3] OFF = Hardwire zones 1 & 2 do not require EOL

resistors (default)

Option [3] ON = Hardwire zones 1 & 2 require EOL resistors

This feature only applies to Magellan’s on-board zone

inputs. Section [095] options [1] and/or [2] (see Zones 15

and 16 become Hardwire Zones on page 18) must be ON in

order to use this feature.

If the hardwire detection devices connected to Magellan’s zone

inputs 1 and 2 have input terminals that require 1K9 end of line

resistors, enable (ON) section [095] option [3]. For details on

using EOL resistors, refer to page 10.

1 2 ... 13 14 15 16 17 18 19 20 21 22 23 ... 44 45

Komentarze do niniejszej Instrukcji

Brak uwag

Magellan Paradox Instrukcja Instalacji Strona 18

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Magellan Paradox