Magellan Paradox Instrukcja Instalacji Pobierz pdf (Strona 19)

Paradox Magellan Systems 19

Wireless Programming

The Magellan system supports up to 16 wireless zones and two

wireless doorbells. These wireless zones are monitored using

transmitters such as wireless detectors and door contacts. The

Magellan console only supports the Paradox Magellan series of

wireless transmitters. The programming of the transmitters is

accomplished in two steps:

1. Assign the wireless transmitter to Magellan.

2. Program the wireless zone.

Assigning Wireless Zone Transmitters

Sections [021] to [036]: Zones 1-16; Wireless Transmitters 1-16

Sections [021] to [036] represent zones 1 to 16. A wireless

transmitter assigned to a section ([021] to [036]) will be assigned

to the zone represented by the section.

For example, a wireless transmitter assigned to section [025] will

be assigned to zone 5.

To assign a wireless transmitter:

1. Access the installer programming mode (page 13).

2. Enter the [

SECTION] corresponding to the desired zone.

3. Enter the 6-digit [SERIAL NUMBER] of the wireless transmitter.

The serial number is located on the inside of the wireless

transmitter.

The wireless transmitters must be activated once having been

assigned to the Magellan console. To activate a transmitter,

insert the batteries and close the cover. To ensure proper

synchronization between the console and the transmitter, open

and close the zone corresponding to the transmitter.

Are the zones that have wireless transmitters assigned to them

programmed? Refer to Zone Definitions on page 15 and Zone

Options on page 17 for more information.

The wireless transmitters can also be assigned through the

Installer menu. Press the [

] key, the [4] key, enter your

[

INSTALLER CODE] and then press the [6] key. Select the zone

you wish to assign the transmitter to, press [

], open the cover

of the transmitter and then close the cover. The transmitter has

been assigned. Refer to the Magellan Quick Setup for more

information on the Installer menu and the assignment of the

wireless transmitters.

Assigning Wireless Doorbells to the Console

Sections [058] and [059]: Wireless Doorbells 1 and 2

Magellan supports the use of two wireless “doorbells”. By

connecting a pushbutton to the Universal Transmitter inputs of a

Magellan Wireless Door Contact (MG-DCT1), the MG-DCT1 will

transmit a signal to Magellan whenever the pushbutton is

pressed. Magellan will in turn become a “doorbell” and play a

predetermined tone (see Wireless Doorbell Tones on page 19).

Please refer to the appropriate Magellan Wireless Door

Contact Instruction for information on the installation and

configuration of the wireless door contact.

To assign a wireless doorbell:

1. Access the installer programming mode (page 13).

2. Enter the [

SECTION] corresponding to the desired doorbell.

3. Enter the 6-digit [

SERIAL NUMBER] of the MG-DCT1.

Wireless Doorbell Tones

Section [096]: Options [1] to [4]

Options [1] and [2] = Set tone for wireless doorbell 1

Options [3] and [4] = Set tone for wireless doorbell 2

Section [096] options [1] to [4] set the tones that will be

played when Magellan receives a signal from either wireless

doorbell 1 or 2 or both. Magellan comes with four tones.

Refer to Table 3 on page 19 to set the desired tone.

Table 3: Wireless Doorbell Tones

Deleting Assigned Wireless Transmitters

Sections [021] to [036]: Zones 1-16; Wireless Transmitters 1-16

Sections [058] and [059]: Wireless Doorbells 1 and 2

To delete an assigned wireless transmitter:

1. Access the installer programming mode (page 13).

2. Enter the [

SECTION] corresponding to the desired zone or

doorbell.

3. Press the [0] key six times to clear the wireless transmitter’s

serial number.

Viewing Wireless Transmitter Signal

Strength

Sections [021] to [036]: Zones 1-16; Wireless Transmitters 1-16

Sections [058] and [059]: Wireless Doorbells 1 and 2

Once wireless transmitters have been installed and assigned to

the Magellan console, the signal strength of each transmitter can

be verified in sections [021] to [036] (zones 1 to 16 respectively)

and sections [058] and [059] (wireless doorbells 1 and 2

respectively). Each section represents the signal strength viewer

for the wireless transmitter assigned to the corresponding zone.

For example, section [021] is the viewer for the wireless

transmitter assigned to zone 1 and section [036] is the viewer for

the wireless transmitter assigned to zone 16.

The signal strength is displayed using two terms:

• “Good”: This is an average reading and is acceptable.

• “Weak”: This is the weakest reading. The transmitter should

be moved to another location. Sometimes moving the

Section [096] - Options [1] and [2] Doorbell Tone #

Option [1] OFF / Option [2] OFF (Doorbell 1) Tone 1 (default)

Option [1] OFF / Option [2] ON (Doorbell 1) Tone 2

Option [1] ON / Option [2] OFF (Doorbell 1) Tone 3

Option [1] ON / Option [2] ON (Doorbell 1) Tone 4

Section [096] - Options [3] and [4] Doorbell Tone #

Option [3] OFF / Option [4] OFF (Doorbell 2) Tone 1

Option [3] OFF / Option [4] ON (Doorbell 2) Tone 2 (default)

Option [3] ON / Option [4] OFF (Doorbell 2) Tone 3

Option [3] ON / Option [4] ON (Doorbell 2) Tone 4

1 2 ... 14 15 16 17 18 19 20 21 22 23 24 ... 44 45

Komentarze do niniejszej Instrukcji

Brak uwag

Magellan Paradox Instrukcja Instalacji Strona 19

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa Magellan Paradox